Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Westchester, CA
Gate installation in Westchester means working with 1940s and 1950s homes on narrow lots, where the original driveway gate is usually a wood picket or chain-link that’s been patched together for decades. The marine layer off Playa del Rey keeps hinges rusting and posts shifting, and the constant jet traffic from LAX means dust and grime settle on every horizontal surface. We install gates that actually hold up here, not gates that look fine for a season and then start binding in the winter wet. If you’re weighing a new gate or a rebuild of your old one, call us at (877) 752-8839 and we’ll walk the job with you.
Why Westchester Homes Are Different
Westchester’s housing stock is mostly post-WWII single-family tract and ranch homes, built tight to the lot line with narrow side yards and shallow setbacks. The original gates from that era, wood picket, chain-link, and the occasional steel swing, are now sixty to eighty years old. The posts are often sunk in concrete from the 1950s, the hinges have been painted over a dozen times, and the latch hardware is at the end of its service life. A repair on these gates is rarely a simple swap of a hinge pin. It’s usually a question of whether the post itself has rotted or the concrete footer has cracked, because in Westchester the ground moisture from the coastal marine layer works its way into everything.
The climate here does a specific kind of damage. Salt-laden air from the LAX basin and Playa del Rey pushes inland through the neighborhood, and it accelerates rust on steel gates, hinges, and latches faster than you’d see in Culver City or Inglewood. Then a Santa Ana event hits, the air goes dry, and wood gates that had swelled tight in the fog suddenly shrink and warp. We see seasonal binding and sagging on a predictable rhythm out here. Add in the grimy film from jet-blast dust that coats gate surfaces a block or two from the airport, and you get hardware that traps moisture against the metal. That’s why Westchester gate work is so often about restoring or retrofitting what’s already there rather than starting fresh.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Main Westchester Services
Most Westchester callers reach out about one of two things: a gate that won’t open or close properly, or an electric operator that’s stopped responding. Here’s how each plays out in this neighborhood.
Gate Repair in Westchester
Older Westchester gates fail in predictable ways: rusted hinge pins, sagging wood pickets, posts that have pulled loose from cracked concrete footers, and latches that no longer line up after decades of settling. Because so many of these homes sit on small lots with mature trees and narrow side yards, we often have to work in tight clearances where a swinging panel can’t be removed easily. We diagnose the actual failure, whether that’s a rotted post base or a bent steel frame, and repair it in place whenever possible. For the full breakdown of what gate repair costs and how long it takes on typical Westchester lots, see Gate Repair in Westchester.
Electric Gate Repair in Westchester
Electric gates out here face the same coastal corrosion as manual gates, but with control boards, safety sensors, and motor housings added to the equation. A Ghost Controls or Mighty Mule operator that works fine inland can develop sensor faults and capacitor failures after a few seasons of salt air near the airport. We carry parts for the major residential and commercial brands Westchester homeowners actually have, and we troubleshoot from the motor down to the keypad, remotes, and photo eyes. If your gate hums but won’t move, or stops halfway and reverses, the problem is usually the operator, not the gate itself. For motor-specific repair and access system troubleshooting, start with Electric Gate Repair in Westchester.
Gate Installation in Westchester
Gate installation in Westchester is a measured, planned job, not a same-day dispatch. The old post-WWII lots are tight, the original fence lines are rarely square after seventy years of settling, and the marine air means the materials you choose determine whether the gate lasts ten years or thirty. We handle everything from a simple wood driveway gate to a full automatic sliding gate with safety edges and an access keypad, and we quote the complete job before any work starts. Whether you want a manual replacement for a rotted picket gate or an electric opener on a new steel frame, the process starts with a site measure and a written price. For the complete scope of what’s involved, see Gate Installation.
Automatic Gate Installation
Signs you need it
You want a gate that opens from inside the car or by keypad, and you’re done with getting out to swing it manually every time.
What it costs in Westchester
Automatic gate installation in Westchester typically runs from $3,500 to $10,000+ depending on gate size, operator brand, and whether you need a new electrical run.
How we do it
We measure the opening and site conditions, spec an operator matched to your gate’s weight and swing or slide path, install the operator arm and safety hardware, then run power and test the full cycle.
Driveway Gate Installation
Signs you need it
Your existing driveway gate is rotted, sagging, or too narrow for modern vehicles, and repairs won’t fix the underlying problem.
What it costs in Westchester
Driveway gate installation in Westchester generally falls between $2,000 and $7,500 for a new gate panel and posts, with materials and the site’s access shaping the final number.
How we do it
We remove the old gate and hardware, set new posts in concrete sized for the gate weight, hang the new panel, and adjust the hinges and latch so the gate swings cleanly without dragging.
Sliding Gate Installation
Signs you need it
Your driveway is short or steep, or your lot doesn’t have room for a swinging gate to arc open.
What it costs in Westchester
Sliding gate installation in Westchester typically costs $4,000 to $12,000 or more, depending on track type, gate length, and whether you’re adding automation.
How we do it
We set the track and support posts, hang the sliding panel, install the roller and guide system, then test the full travel path and adjust the stops so the gate settles open and closed without slamming.
What Gate Installation Costs in Westchester
| Item | Typical range in Westchester |
|---|---|
| Manual driveway gate (wood or steel) | $1,500 – $5,000 |
| Automatic gate operator and install | $3,500 – $10,000+ |
| Full automatic gate system with access control | $8,000 – $20,000+ |
Do I need a permit to install a gate in Westchester?
Most standard residential gate replacements in Westchester don’t require a permit, but automatic gates with new electrical runs often do. We check the local requirements for your specific site before we quote, so there are no surprises after the work starts.
How long does gate installation take in Westchester?
A typical manual gate installation in Westchester takes one to two days from removal through adjustment. Automatic gates usually run two to three days because of the electrical run, operator install, and safety sensor testing.
Brands We Service in Westchester
We work on the brands Westchester homes actually have installed, including Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common parts for these systems locally, which means less waiting on a factory order when a control board or safety sensor fails. For the full list of brands and what we can source, see our brands.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Westchester, CA
| Service | Typical range in Westchester |
|---|---|
| Manual gate repair | $150 – $600 |
| Electric gate repair | $200 – $900 |
| Gate opener replacement | $800 – $2,500 |
| Control board replacement | $400 – $1,200 |
| Hinge replacement | $100 – $400 |
| Post replacement | $500 – $2,000 |
| Manual gate installation | $1,500 – $5,000 |
| Automatic gate installation | $3,500 – $10,000+ |
| Full automatic system with access control | $8,000 – $20,000+ |
| Safety sensor replacement | $150 – $450 |
In Westchester, the biggest price drivers are post condition, access width, and whether your gate needs a new electrical run. Older homes near the airport basin often have rotted or cracked post footers that must be dug out and repoured, which adds labor hours. We quote every job before work starts, and the price you approve is the price you pay.
Neighborhoods We Serve in Westchester
We cover all of the 90045 ZIP code and the surrounding Westchester area. Most of our calls come from the streets between Lincoln Boulevard and Sepulveda, and from the blocks closer to Loyola Marymount and the bluff toward Playa del Rey. Typical response time for a repair call in Westchester is same-day or next-day, depending on the time you call.
- North Westchester
- Westchester Triangle
- Loyola Village
- Bluff Creek
- Westport Heights
Service Area – Cities Near Westchester
We run gate repair and installation calls from Westchester down through the beach communities and east toward the Crenshaw corridor. If you’re in Playa Vista, CA, Hyde Park South, CA, Morningside Park, CA, or Crenshaw, CA, we can usually slot you into the same route as our Westchester work.
Serving Westchester, CA – Our Local Coverage Area
We’re based in the Westchester area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Westchester
For manual gate failures and most electric gate problems, we can typically arrive in Westchester the same day you call or first thing the next morning. Emergency calls for a gate stuck open or blocking a driveway get priority on the schedule.
Some Westchester condo complexes and gated communities do require architectural review before you change a gate’s style or height. We can provide the specs and drawings your HOA board needs, and we’ll match the existing neighborhood style when that’s part of the approval.
Yes. Rusted hinges, latches, and steel frames are the most common gate failures we see in Westchester, driven by the salt air from the coast and the moisture that sits in the LAX basin. We replace the corroded hardware and treat or replace the affected steel so the repair holds.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within the hour.
- 4You approve before work beginsNothing starts until you say go.
What Westchester Customers Say
"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Vikram Gupta"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, had one with him, and we were moving cars again in under an hour."
- Justin Park"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Nathan Quinn