Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Hyde Park South Homeowners
A gate that won’t open isn’t just a hassle. It traps your car in the driveway, blocks deliveries, and leaves your property half-secured. Gate Repair Hyde Park South fixes that. Led by Mitch Calderon, our team works on the gate you already own, whether it’s a Mighty Mule on a single-family driveway or a FAAC system running a commercial lot. We stock OEM parts for the brands Hyde Park South actually uses, so the diagnostic is faster and the fix lasts. Call (877) 752-8839 for same-day service when your gate is down.
Key Takeaways
- We work on your brand: OEM parts for LiftMaster, FAAC, Mighty Mule, and Elite systems, not universal workarounds.
- Same-day repair available for most mechanical and electric gate failures in Hyde Park South.
- Price is quoted and agreed before any work starts, so there are no surprises on the invoice.
- From the motor to the keypad: we fix the mechanical, electric, and access control sides of your gate.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Driveway Gate Repair
Driveway Gate Repair covers the gate that controls access to your home, the one you use every day without thinking about until it stops mid-cycle or groans like it’s given up. In Hyde Park South we see a lot of single-family driveway gates with worn hinges, dead operator motors, and keypads that have given up reading codes. We diagnose the whole system at once, so a sticking wheel or bent track gets caught before it burns out a motor. A typical driveway gate repair in Hyde Park South runs $180 to $340 depending on parts and what’s failed. Call (877) 752-8839 for an exact quote, free.
Operator and Motor Diagnosis
The motor is usually the first thing blamed and often the last thing actually broken. We test voltage at the board, load on the motor, and the condition of limit switches before recommending a replacement. That saves you from paying for a new operator when the real fault is a $12 capacitor or a misaligned safety sensor.
Track, Wheel, and Hinge Work
A driveway gate that drags or binds puts twice the load on the operator. We replace worn rollers, repair bent track sections, and re-hang gates that have sagged on their hinges. The goal is a gate that swings or slides without fighting the motor.
Gate Welding
Gate Welding is the repair you need when metal actually breaks rather than just wearing out, a cracked weld at a hinge point, a snapped picket, a frame corner that’s separated from years of wind load. Not every gate company welds. We do, on-site in Hyde Park South, with mobile MIG and stick equipment. Repair welding on a standard steel or iron gate runs $150 to $400 depending on the extent of the cracking and whether we need to reinforce the section with plate. Call (877) 752-8839 and we’ll give you a number before we strike an arc.
Cracked Frame and Hinge Repair
The hinge plate is where most welded gates fail, because it takes every ounce of torque the gate generates. We grind out the old crack, weld it back solid, and often add a gusset plate so the same failure doesn’t come back next season. If the gate is powder-coated, we’ll tell you exactly what the finish repair involves before we start.
Picket and Rail Replacement
A bent picket or a rail that’s rusted through from the inside compromises more than looks. We cut out the damaged section and weld in matched material, so the gate keeps its lines and its strength. On ornamental iron work we match the profile as closely as the steel suppliers in this area allow.
Commercial Gate Repair
Commercial Gate Repair means keeping a gate that cycles hundreds of times a day running like it can’t afford to stop, because it can’t. Property managers in Hyde Park South call us for FAAC and BFT operators, broken safety loops, and access systems that stopped talking to the gate. We work on the brands commercial properties actually run, with OEM parts instead of whatever fits. Commercial repairs typically run $250 to $700 depending on the operator and what’s failed, and we quote the full price before we begin. Call (877) 752-8839 to schedule.
Operator and Control Board Service
Commercial operators are not residential motors with a bigger case. We diagnose control boards, check capacitor health, and test the duty cycle under real load. If a FAAC or BFT board has failed, we replace it with the matching OEM board, not a knockoff that causes glitches three months later.
Safety Loop and Access Integration
A gate that closes on a car because the loop detector is dead isn’t a gate that works, it’s a liability. We test and replace vehicle detection loops, photo eyes, and access keypad wiring so the gate stops and reverses exactly the way the manufacturer intended. That includes making sure the fire department override works if the property requires one.
Iron Gate Repair
Iron Gate Repair covers the heavy, ornamental gates that frame older Hyde Park South homes and a lot of mid-century apartment entries. These gates rust from the inside at ground level, crack at the hinge welds, and eventually seize if nobody catches it early. We repair rather than replace wherever the steel is still sound. Typical iron gate repair runs $200 to $500, including welding, hinge replacement, and rust treatment where needed. Call (877) 752-8839 for an on-site assessment.
Rust and Corrosion Treatment
Rust isn’t cosmetic on an iron gate, it’s structural. We grind affected areas back to clean metal, treat with a rust converter, and prime before the gate goes back into service. If the bottom rail is too far gone, we’ll tell you straight rather than painting over a problem that’ll fail within a year.
Ornamental Hinge and Latch Replacement
Old iron gates often used hinges and latches you can’t just pick up at a hardware store. We source period-appropriate or custom-fabricated replacements so the hardware matches the gate’s look and carries its weight properly. A mismatched hinge from a big-box store is how a lot of these gates get damaged in the first place.
Sliding Gate Repair
Sliding Gate Repair addresses the cantilever and V-track gates that are everywhere in Hyde Park South commercial lots and larger residential properties. When a sliding gate starts grinding, hesitating mid-travel, or shaking as it moves, you’re usually looking at wheel or track wear, or an operator that’s fighting a gate that no longer rolls true. We fix the rolling gear first, then address the motor. Sliding gate repairs typically run $200 to $550 depending on the hardware. Call (877) 752-8839 and we’ll diagnose it on site.
Roller, Wheel, and Track Service
Sliding gates live or die on their rolling gear. We replace flat-spotted rollers, bent track sections, and guides that have been nudged out of alignment by delivery trucks or tree roots. Getting the gate rolling freely again often solves what looks like a motor problem without touching the motor.
Operator Adjustment and Limit Reset
Once the gate rolls properly, we set the limits so it opens fully and closes fully without slamming or stopping short. Improper limits are a common reason sliding gates fail early, and it takes about ten minutes to do right. We check gearbox oil and chain or belt tension at the same time.
Wrought Iron Gate Repair
Wrought Iron Gate Repair is the ornamental subset of iron work, think hand-forged details, curved pickets, scrollwork that hasn’t been made in seventy years. Hyde Park South has some beautiful old wrought iron, and most of it needs more than a rattle-can fix. We repair wrought work with matched welding techniques and careful finish matching. Expect $250 to $600 for structural wrought iron repair, depending on how much ornate detail has to be reproduced or reinforced. Call (877) 752-8839 to have us look.
Scrollwork and Decorative Element Repair
When a scroll or finial breaks, the right fix isn’t cutting the whole section out. We weld the broken piece back in place, fabricate a replacement section when the original is gone, and finish it so the repair doesn’t stand out like a patch. This is slow work done carefully, and we charge for the time it actually takes.
Full Gate Straightening and Re-Hanging
A wrought iron gate that’s sagged or twisted puts strain on every joint and weld. We straighten the frame, re-weld loose joints, and re-hang the gate on new hinges so it swings balanced. The gate gets a service life extension rather than a one-symptom patch job.
Metal Gate Repair
Metal Gate Repair is the broad category that covers steel, aluminum, and iron gates of all types, from a basic chain-link vehicle gate to a heavy steel commercial barrier. In Hyde Park South, we repair what’s practical to repair: frames, hinges, posts, infill panels, and the hardware that holds it together. Most metal gate repairs run $150 to $450, with structural steel and welding pushing toward the higher end. Call (877) 752-8839 for a straight number.
Post and Frame Repair
A leaning post is the root cause of a lot of gate failures, and it’s the first thing we check. We plumb and re-set posts, sleeve damaged post bases, and repair frame members that have been hit by vehicles. The gate can’t work right if what it hangs from isn’t solid.
Hardware and Latch Replacement
Latches, drop rods, cane bolts, hinges: the small parts fail first and cause the biggest inconveniences. We replace worn hardware with commercial-grade parts sized for the gate, not the light-duty residential stuff that strips out in a year. Drilling a new hole in a gate rail to make a wrong-size latch fit is not a repair, and we won’t do it.
Wood Gate Repair
Wood Gate Repair covers the driveway and side-yard wood gates that are common on older Hyde Park South properties and newer privacy fences. Wood gates sag because the joinery gives out, not because the wood itself fails. We rebuild the frame with proper diagonal bracing, replace rotted members, and re-hang the gate so it doesn’t drag. Wood gate repair typically runs $180 to $400 depending on size and how much lumber needs replacing. Call (877) 752-8839 for an estimate.
Frame Rebuild and Bracing
A wood gate that sags has usually lost its diagonal brace or the frame joints have separated. We rebuild the frame with the correct brace orientation so the gate remains square under its own weight. This is the difference between a fix that lasts and one that sags again by fall.
Rotted Member Replacement
Ground contact is where wood gates rot first, usually the bottom rail or the hinge-side stile. We cut out the rot and splice in pressure-treated or cedar replacement stock, then paint or stain to match. If the hinge screws can’t bite solid wood, the gate will pull off the post eventually, so this is a structural repair, not a cosmetic one.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We service LiftMaster daily in Hyde Park South. Their residential operators are on thousands of driveways here, and we stock the common control boards, limit switches, and remotes. When a LiftMaster gate stops responding to the remote or doesn’t stop at the limits, we know which part to check first.
We work extensively on Mighty Mule, the most common DIY-installed driveway operator in the area. These systems fail when the installation was rushed or the power supply is inadequate. We correct the install issues and replace the failed components with genuine Mighty Mule parts. For commercial properties, we service FAAC and Elite operators, including the hydraulic FAAC units that most repair shops won’t touch. Whether you have a LiftMaster, Mighty Mule, FAAC, Elite, or any other make, we can help.
Signs You Need a Pro Right Now
- The gate stops mid-cycle and reverses or just quits. This points to a limit switch, a safety sensor, or a motor overheating. Continuing to force it open by hand can damage the operator further. We diagnose the actual cause instead of resetting the system and hoping.
- You hear grinding, shrieking, or a metal-on-metal scrape. That’s usually a bearing, a roller, or a gear that’s already failed or about to. Running a gate with a bad bearing chews up the shaft and turns a small fix into an operator replacement.
- The gate is visibly sagging or dragging on the ground. When a gate drags, the motor works harder, the hinges bend, and the welds crack. The fix is mechanical, not electrical, and it should be addressed before the operator burns out.
- The keypad, remote, or access system has stopped working. If the gate works manually but not from the controls, you have an access system fault. It could be a receiver, a board, or the keypad itself. We test each point and replace only what’s dead.
- The gate slams shut instead of stopping at its limit. A gate that doesn’t stop where it should is dangerous. This is a limit adjustment or replacement, and it’s a safety issue, not a nuisance. We set limits so the gate closes the way the manufacturer designed it to.
Our Process, Step by Step
- 1
Call and describe what’s happening. Tell us the brand if you know it, and what the gate is doing or not doing. That lets us bring the most likely parts. Call (877) 752-8839 and we’ll ask the right questions.
- 2
On-site diagnosis. We test the system from the power source to the gate itself: voltage at the board, condition of the operator, mechanical state of the gate, and function of every safety and access component. You get a clear explanation of what’s failed and what it will take to fix it.
- 3
Written price, agreed before work begins. The number we quote is the number you pay. If a repair reveals a hidden problem, we stop and re-quote. There’s no running tab and no surprise at the end.
- 4
The repair itself. We use OEM parts for the brands we service, and commercial-grade hardware for structural work. Welding is done on-site when access allows. Every job is tested through multiple cycles before we leave.
- 5
Final walkthrough and care notes. We show you what was replaced, what it does, and what to watch for going forward. You’ll know how to keep the gate running, and you’ll have our number if anything changes.
How Much Does Gate Repair Cost in Hyde Park South?
What affects the price is the brand, the age of the system, and whether the failure is mechanical, electric, or structural. Older operators sometimes aren’t worth rebuilding when the replacement board costs more than a new unit, and we’ll tell you that outright. The way to avoid overpaying is to get a diagnosis that separates the actual failure from nearby parts that are still fine. Our free estimate includes the diagnosis, the parts list with prices, and the labor, itemized, before anything is approved. Call (877) 752-8839 and we’ll give you the real number for your gate.
Our Service Area Near Hyde Park South
We serve Hyde Park South and the surrounding neighborhoods including Leimert Park, Morningside Park, Baldwin Hills, Jefferson Park, University Park, and Arlington Heights. Most repair calls in the immediate area get same-day or next-day service. If you’re in a gated community in Crenshaw or managing a property in Vermont Vista, we handle Gate Repair in Leimert Park and the wider Mid-City area the same way. See our home page for service details, or check our guide to Gate Repair in Hyde Park South for more on what we do. If your gate is in Morningside Park, visit Gate Repair in Morningside Park for area-specific information.
Serving Hyde Park South, CA – Our Local Coverage Area
We’re based in the Hyde Park South area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Hyde Park South
What is gate repair?
Gate repair is the work of diagnosing and fixing what’s wrong with a residential or commercial gate, whether that’s a mechanical hinge failure, a structural crack, or an electric operator that won’t respond. It covers the gate itself, the hardware that hangs it, and the motor and access controls that operate it. At Gate Repair Hyde Park South, we repair the full system, from the motor to the keypad. Call (877) 752-8839 and describe the symptom, and we’ll tell you what you’re likely dealing with.
How long does a gate repair take?
Most repairs are completed the same day we arrive. A hinge replacement or limit switch adjustment takes under an hour. A control board replacement or weld repair takes longer, usually two to three hours from diagnosis to tested completion. If a part has to be ordered for a specific brand like FAAC, we’ll tell you the lead time before any work is scheduled. Call (877) 752-8839 for a time estimate on your specific gate.
How much does gate repair cost in Hyde Park South?
Most gate repairs in Hyde Park South cost between $180 and $600, with the typical job landing around $250 to $400. The final number depends on the brand, the part that failed, and whether welding or structural work is required. We quote the full price before any work starts, so the number we give you is the number you pay. Estimates are free, and there’s no obligation. Call (877) 752-8839 for an exact quote.
Do you service LiftMaster and Mighty Mule gates?
Yes. LiftMaster and Mighty Mule are the two brands we see most in Hyde Park South residential driveways, and we carry their OEM parts in stock. We also service FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, and Elite systems. If your gate brand isn’t on that list, call (877) 752-8839 anyway. If it operates a gate, we’ve likely worked on it.
Is emergency gate repair available?
A gate stuck open or stuck closed on a driveway or commercial lot is an emergency, and we treat it that way. Same-day service is available for most failures in Hyde Park South and the surrounding neighborhoods. If you’re locked out of your driveway or your commercial gate won’t secure, call (877) 752-8839 and tell us it’s urgent.
Is there a warranty on gate repairs?
We stand behind our workmanship, and the OEM parts we install carry their manufacturer warranty. The specific terms depend on what was repaired and which brand of part was used, and we’ll provide the details in writing on your quote. Before any work starts, you’ll know exactly what’s covered and for how long. Call (877) 752-8839 and we’ll answer warranty questions for your specific repair.
How do I prepare for a gate repair visit?
Clear access to the gate and the operator is the main thing. If it’s a driveway gate, make sure a vehicle can reach it and the area around the operator is clear. If it’s a commercial gate, let us know who’ll provide access to the control box or keypad. You don’t need to have any tools or parts ready. We bring everything needed for diagnosis and most repairs. Call (877) 752-8839 and we’ll walk you through what to expect.
Schedule Your Gate Repair Service in Hyde Park South Today
Your gate should be back open today. Call (877) 752-8839 and tell us what it’s doing, or not doing. We’ll get a technician to your Hyde Park South property, diagnose the problem, and give you a written price before any work begins. Estimates are free, and there’s no obligation. Gate back open today, installed right so the repair call doesn’t come back.
Written by Mitch Calderon, Owner at Gate Repair Hyde Park South, serving Hyde Park South and surrounding neighborhoods.